Engine Identification - Snowmobile World : Your #1 Snowmobile Forum
http://www.snowmobileworld.com/forums
» Sponsors
Go Back   Snowmobile World : Your #1 Snowmobile Forum > SNOWMOBILING SECTION > POLARIS

Reply
 
Thread Tools
Old 01-23-2009, 01:32 PM   #1
SHalloway
Junior Member
 
Join Date: Jan 2009
Posts: 2
Default Engine Identification

I have two scrapped Polaris snowmobiles that I am looking to combine into one usable machine. One is an Indy Trail Deluxe, engine serial number (from the flywheel housing) 9205233, which I think is a 1993. The other number on the flywheel housing is EC443PM00122073.

The other one is an Indy Trail Supertrak, engine serial number 9000988 from a sticker on the flywheel housing, but no other apparent number on the housing. I was told this was a 1991 snowmobile.

I am trying to determine what engines are in these 2 machines based on the numbers I listed above. Can anyone help me interpret them?
SHalloway is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 01-24-2009, 03:16 PM   #2
retiredpop
Senior Member
 
retiredpop's Avatar
 
Join Date: May 2001
Location: Calgary,Alberta
Mileage: 35,000 miles +
Primary Sled: 2010 RMK600
Where I sled: AB, BC, MT
Posts: 642
Default

The ECM44.. designates a 440 fan cooled sled.
__________________
The older I get the better I was; In fact now that I think about it I am a legend.
retiredpop is offline   Reply With Quote
Old 01-24-2009, 11:33 PM   #3
162Whiskey
Senior Member
 
162Whiskey's Avatar
 
Join Date: Mar 2008
Location: Alaska - 63North, 162West
Mileage: More than the knees can take!
Primary Sled: Arctic Cat T570
Where I sled: Bering Sea coast
Posts: 476
Default

Pop is correct. The EC44 is a 440 fan; the 488 fan is marked EC50. You will also find additional marks, at least on the cylinder castings, like 2PM or 3PM which indicate the series of the motor; the lower number being earlier. Many of these old engines will interchange cranks and crankcases with only the cylinder making the difference in size of the engine. (Of course they need to be carbed properly.)

I would not necessarily trust the fan shroud or flywheel - or even crankcase- to determine what the engine size is. You'll need to look at the cylinder castings.

A trail with a 440 would have been an earlier model as they went with the 488 for many years - until switching yet again to the 550.

The only thing I'd be much concerned about is using matching case halves to start. I've put a number of these older fan engines together without worrying about the crankcase component origins. Use the parts you have which are in the best condition and make sure electrical, fuel, and clutch are right and you should be good.

People here will help you with specific specs if you needs them.
__________________
Formerly known as 63November, and before that as Golsovia.

Riding since 1983.

-Scorpion Whip
-Ski-Doo Skandic
-Yamaha Enticer LTs
-Polaris Trails

Current:
-99 Arctic Cat 550 Panther 14,000+ miles
-08 Ski-Doo 550 Backcountry
-340 eBay Edge from AK, and 10+ other states
-'11 AC T570 brand new...4000 miles

Last edited by 162Whiskey; 01-24-2009 at 11:38 PM.
162Whiskey is offline   Reply With Quote
Old 01-29-2009, 09:29 AM   #4
Beaumod
Junior Member
 
Join Date: Jan 2009
Posts: 3
Default

Pop and Whiskey,

Was hoping you could help me as well. I'm helping my Dad fix what we think is a 1988 Polaris Indy 400. However it's a bit of a frankinmobile and were not sure. It needs a new Ignition Coil but I'm not positive what engine I have. The engine code is EC40PL-02. Do you folks know of a website that I could look up the engine so I know what parts to purchase for it? Thanks in advance!

Derek from Detroit
Beaumod is offline   Reply With Quote
Old 01-29-2009, 10:35 AM   #5
retiredpop
Senior Member
 
retiredpop's Avatar
 
Join Date: May 2001
Location: Calgary,Alberta
Mileage: 35,000 miles +
Primary Sled: 2010 RMK600
Where I sled: AB, BC, MT
Posts: 642
Default

You have a 398 cc liquid cooled engine used in the Indy 400. You don't have enough information for the year although for most engine parts that is not really that important. Do you have a serial number on that engine? The parts fiche I use for older sleds is

http://www.ronnies.com/micro.htm
__________________
The older I get the better I was; In fact now that I think about it I am a legend.
retiredpop is offline   Reply With Quote
Old 01-29-2009, 11:01 AM   #6
162Whiskey
Senior Member
 
162Whiskey's Avatar
 
Join Date: Mar 2008
Location: Alaska - 63North, 162West
Mileage: More than the knees can take!
Primary Sled: Arctic Cat T570
Where I sled: Bering Sea coast
Posts: 476
Default

A couple of the nice things about some of those older engines is that they used some of the same parts on various machines. If it is the exciter coil you need, it is likely the same as the one also used on the 500 liquids and perhaps some of the others. Further, the part (which is available) is very inexpensive as electrical parts go - about $60.

I suspect some of the old CDIs may cross-over. Unfortunately, many of the CDIs which are getting close to 20 years old and older are no longer listed as available. Consequently, some of the typical Polaris fiches don't show the part number.
__________________
Formerly known as 63November, and before that as Golsovia.

Riding since 1983.

-Scorpion Whip
-Ski-Doo Skandic
-Yamaha Enticer LTs
-Polaris Trails

Current:
-99 Arctic Cat 550 Panther 14,000+ miles
-08 Ski-Doo 550 Backcountry
-340 eBay Edge from AK, and 10+ other states
-'11 AC T570 brand new...4000 miles
162Whiskey is offline   Reply With Quote
Old 01-29-2009, 12:49 PM   #7
Beaumod
Junior Member
 
Join Date: Jan 2009
Posts: 3
Default

Thanks Pops and Whiskey,

I'll see if we can find the serial number, I'm guessing you know exactly where to look for it...? Thanks again for all your help. I'll post a note when complete.

Regards,

Derek from Detroit
Beaumod is offline   Reply With Quote
Old 01-29-2009, 12:52 PM   #8
retiredpop
Senior Member
 
retiredpop's Avatar
 
Join Date: May 2001
Location: Calgary,Alberta
Mileage: 35,000 miles +
Primary Sled: 2010 RMK600
Where I sled: AB, BC, MT
Posts: 642
Default

The CDI is listed under Magneto 400 as part no. 3083989. Interestingly though it is only shown under the 1990 and 1991 model years. I am sure it is the same one as for your sled though. It is about $315.
__________________
The older I get the better I was; In fact now that I think about it I am a legend.
retiredpop is offline   Reply With Quote
Old 01-29-2009, 12:58 PM   #9
Beaumod
Junior Member
 
Join Date: Jan 2009
Posts: 3
Default

woah... 18 CDI UNIT
3083989 1 $314.99

More than I expected. Thanks a bunch.
Beaumod is offline   Reply With Quote
Old 01-29-2009, 01:56 PM   #10
retiredpop
Senior Member
 
retiredpop's Avatar
 
Join Date: May 2001
Location: Calgary,Alberta
Mileage: 35,000 miles +
Primary Sled: 2010 RMK600
Where I sled: AB, BC, MT
Posts: 642
Default

Quote:
Originally Posted by Beaumod View Post
woah... 18 CDI UNIT
3083989 1 $314.99

More than I expected. Thanks a bunch.
Yeah, I know! Do you have any used sled parts businesses around you? I know some of the 500 liquid cooled engines used the same CDI also.
__________________
The older I get the better I was; In fact now that I think about it I am a legend.
retiredpop is offline   Reply With Quote
Sponsored Links
Advertisement
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Powered by vBadvanced CMPS v3.2.2

All times are GMT -5. The time now is 10:58 PM.



Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.